JINXING MATECH CO LTD
JINXING MATECH is an expert provider on the metal solution. Especially on the products such as Tungsten Alloy , Tungsten copper , Titanium , Zirconium, Vanadium, Hafnium, Sputtering target , Nobel
Add to Cart
Titanium Rod, Forging rod ,(Round, Square, Rectangle and Hexagon, etc.). ASTM B348, AMS 4928, AMS 6921, AMS 4975, AMS 4978, AMS 4966, AMS4930, AMS6932 , ASTM F67, ASTM F136, ASME SB863, AWS A5.16, etc. H7/h7 tolerance is available. Material Grade: GR1, GR2, GR3,GR4, GR5, GR7, GR9, GR12, GR16, GR17, GR23, Ti-6Al-4V ELI, Ti-3-8-6-4-4, Ti-6-2-4-2, Ti-6-6-2, Ti-5-2.5, Ti-15-3-3-3, Ti6Al7
Chemical content:
| N | C | H | Fe | O | Al | V | Pa | Mo | Ni | Ti | |
| Gr 1 | 0.03 | 0.08 | 0.015 | 0.20 | 0.18 | / | / | / | / | / | bal |
| Gr 2 | 0.03 | 0.08 | 0.015 | 0.30 | 0.25 | / | / | / | / | / | bal |
| Gr 3 | 0.05 | 0.08 | 0.015 | 0.30 | 0.35 | / | / | / | / | / | bal |
| Gr 4 | 0.05 | 0.08 | 0.015 | 0.50 | 0.40 | / | / | / | / | / | bal |
| Gr 5 | 0.05 | 0.08 | 0.015 | 0.40 | 0.20 | 5.5~6.75 | 3.5~4.5 | / | / | / | bal |
| Gr 7 | 0.03 | 0.08 | 0.015 | 0.30 | 0.25 | / | / | 0.12~0.25 | / | / | bal |
| Gr 9 | 0.03 | 0.08 | 0.015 | 0.25 | 0.15 | 2.5~3.5 | 2.0~3.0 | / | / | / | bal |
| Gr12 | 0.03 | 0.08 | 0.015 | 0.30 | 0.25 | / | / | / | 0.2~0.4 | 0.6~0.9 | bal |
Testing:
Tensile Strength
Yield Strength
Fracture toughness
Liquid penetrant
Ultrasonic
Technical requirements:
1. The chemical composition of titanium and titanium alloy rods shall comply with the requirements of ASTM B348.
When repeated inspection is required, the allowable deviation of the chemical composition
shall comply with the requirements of ASTM B348.
2, hot working rod diameter or side length of their tolerance to comply with Table one.
3. After hot working, the diameter of the cold-drawn bar should be in accordance with industry regulations.
4. The out-of-roundness of the bar after lapping (grinding) after hot working should not be more than half of its dimensional tolerance.
5. The indefinite length of the processed bar is 300-6000mm, the indefinite length of the annealed bar is 300-2000mm,
and the fixed or double length should be within the range of the indefinite length. The allowed deviation of the fixed length is + 20mm
The length of the ruler should also be included in the cut of the bar, each cut is 5mm.
The length of the ruler or ruler should be specified in the contract.
